diff --git a/charts/vpn-mesh-config/lighthouse.yaml b/charts/vpn-mesh-config/lighthouse.yaml
deleted file mode 100644
index cf106b5..0000000
--- a/charts/vpn-mesh-config/lighthouse.yaml
+++ /dev/null
@@ -1,246 +0,0 @@
-# This is the nebula example configuration file. You must edit, at a minimum, the static_host_map, lighthouse, and firewall sections
-# Some options in this file are HUPable, including the pki section. (A HUP will reload credentials from disk without affecting existing tunnels)
-
-# PKI defines the location of credentials for this node. Each of these can also be inlined by using the yaml ": |" syntax.
-pki:
-  # The CAs that are accepted by this node. Must contain one or more certificates created by 'nebula-cert ca'
-  ##ca: /etc/nebula/ca/ca.crt
-  ca: /etc/nebula/lighthouse/ca.crt
-  cert: /etc/nebula/lighthouse/host.crt
-  key: /etc/nebula/lighthouse/host.key
-  #blocklist is a list of certificate fingerprints that we will refuse to talk to
-  #blocklist:
-  #  - c99d4e650533b92061b09918e838a5a0a6aaee21eed1d12fd937682865936c72
-
-# The static host map defines a set of hosts with fixed IP addresses on the internet (or any network).
-# A host can have multiple fixed IP addresses defined here, and nebula will try each when establishing a tunnel.
-# The syntax is:
-#   "{nebula ip}": ["{routable ip/dns name}:{routable port}"]
-# Example, if your lighthouse has the nebula IP of 192.168.100.1 and has the real ip address of 100.64.22.11 and runs on port 4243:
-static_host_map:
-  "<INTERNAL_IP>": ["<EXTERNAL_IP>:<PORT>"]
-
-
-lighthouse:
-  # am_lighthouse is used to enable lighthouse functionality for a node. This should ONLY be true on nodes
-  # you have configured to be lighthouses in your network
-  am_lighthouse: true
-  # serve_dns optionally starts a dns listener that responds to various queries and can even be
-  # delegated to for resolution
-  #serve_dns: false
-  #dns:
-    # The DNS host defines the IP to bind the dns listener to. This also allows binding to the nebula node IP.
-    #host: 0.0.0.0
-    #port: 53
-  # interval is the number of seconds between updates from this node to a lighthouse.
-  # during updates, a node sends information about its current IP addresses to each node.
-  interval: 60
-  # hosts is a list of lighthouse hosts this node should report to and query from
-  # IMPORTANT: THIS SHOULD BE EMPTY ON LIGHTHOUSE NODES
-  # IMPORTANT2: THIS SHOULD BE LIGHTHOUSES' NEBULA IPs, NOT LIGHTHOUSES' REAL ROUTABLE IPs
-  hosts:
-    # - "111.0.0.1"
-
-  # remote_allow_list allows you to control ip ranges that this node will
-  # consider when handshaking to another node. By default, any remote IPs are
-  # allowed. You can provide CIDRs here with `true` to allow and `false` to
-  # deny. The most specific CIDR rule applies to each remote. If all rules are
-  # "allow", the default will be "deny", and vice-versa. If both "allow" and
-  # "deny" rules are present, then you MUST set a rule for "0.0.0.0/0" as the
-  # default.
-  #remote_allow_list:
-    # Example to block IPs from this subnet from being used for remote IPs.
-    #"172.16.0.0/12": false
-
-    # A more complicated example, allow public IPs but only private IPs from a specific subnet
-    #"0.0.0.0/0": true
-    #"10.0.0.0/8": false
-    #"10.42.42.0/24": true
-
-  # local_allow_list allows you to filter which local IP addresses we advertise
-  # to the lighthouses. This uses the same logic as `remote_allow_list`, but
-  # additionally, you can specify an `interfaces` map of regular expressions
-  # to match against interface names. The regexp must match the entire name.
-  # All interface rules must be either true or false (and the default will be
-  # the inverse). CIDR rules are matched after interface name rules.
-  # Default is all local IP addresses.
-  #local_allow_list:
-    # Example to block tun0 and all docker interfaces.
-    #interfaces:
-      #tun0: false
-      #'docker.*': false
-    # Example to only advertise this subnet to the lighthouse.
-    #"10.0.0.0/8": true
-
-# Port Nebula will be listening on. The default here is 4243. For a lighthouse node, the port should be defined,
-# however using port 0 will dynamically assign a port and is recommended for roaming nodes.
-listen:
-  # To listen on both any ipv4 and ipv6 use "[::]"
-  host: "[::]"
-  port: <PORT>
-  # Sets the max number of packets to pull from the kernel for each syscall (under systems that support recvmmsg)
-  # default is 64, does not support reload
-  #batch: 64
-  # Configure socket buffers for the udp side (outside), leave unset to use the system defaults. Values will be doubled by the kernel
-  # Default is net.core.rmem_default and net.core.wmem_default (/proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_default)
-  # Maximum is limited by memory in the system, SO_RCVBUFFORCE and SO_SNDBUFFORCE is used to avoid having to raise the system wide
-  # max, net.core.rmem_max and net.core.wmem_max
-  #read_buffer: 10485760
-  #write_buffer: 10485760
-
-# EXPERIMENTAL: This option is currently only supported on linux and may
-# change in future minor releases.
-#
-# Routines is the number of thread pairs to run that consume from the tun and UDP queues.
-# Currently, this defaults to 1 which means we have 1 tun queue reader and 1
-# UDP queue reader. Setting this above one will set IFF_MULTI_QUEUE on the tun
-# device and SO_REUSEPORT on the UDP socket to allow multiple queues.
-#routines: 1
-
-punchy:
-  # Continues to punch inbound/outbound at a regular interval to avoid expiration of firewall nat mappings
-  punch: true
-
-  # respond means that a node you are trying to reach will connect back out to you if your hole punching fails
-  # this is extremely useful if one node is behind a difficult nat, such as a symmetric NAT
-  # Default is false
-  #respond: true
-
-  # delays a punch response for misbehaving NATs, default is 1 second, respond must be true to take effect
-  #delay: 1s
-
-# Cipher allows you to choose between the available ciphers for your network. Options are chachapoly or aes
-# IMPORTANT: this value must be identical on ALL NODES/LIGHTHOUSES. We do not/will not support use of different ciphers simultaneously!
-cipher: chachapoly
-
-# Local range is used to define a hint about the local network range, which speeds up discovering the fastest
-# path to a network adjacent nebula node.
-#local_range: "172.16.0.0/24"
-
-# sshd can expose informational and administrative functions via ssh this is a
-#sshd:
-  # Toggles the feature
-  #enabled: true
-  # Host and port to listen on, port 22 is not allowed for your safety
-  #listen: 127.0.0.1:2222
-  # A file containing the ssh host private key to use
-  # A decent way to generate one: ssh-keygen -t ed25519 -f ssh_host_ed25519_key -N "" < /dev/null
-  #host_key: ./ssh_host_ed25519_key
-  # A file containing a list of authorized public keys
-  #authorized_users:
-    #- user: steeeeve
-      # keys can be an array of strings or single string
-      #keys:
-        #- "ssh public key string"
-
-# Configure the private interface. Note: addr is baked into the nebula certificate
-tun:
-  # When tun is disabled, a lighthouse can be started without a local tun interface (and therefore without root)
-  disabled: false
-  # Name of the device
-  dev: nebula1
-  # Toggles forwarding of local broadcast packets, the address of which depends on the ip/mask encoded in pki.cert
-  drop_local_broadcast: false
-  # Toggles forwarding of multicast packets
-  drop_multicast: false
-  # Sets the transmit queue length, if you notice lots of transmit drops on the tun it may help to raise this number. Default is 500
-  tx_queue: 500
-  # Default MTU for every packet, safe setting is (and the default) 1300 for internet based traffic
-  mtu: 1300
-  # Route based MTU overrides, you have known vpn ip paths that can support larger MTUs you can increase/decrease them here
-  routes:
-    #- mtu: 8800
-    #  route: 10.0.0.0/16
-  # Unsafe routes allows you to route traffic over nebula to non-nebula nodes
-  # Unsafe routes should be avoided unless you have hosts/services that cannot run nebula
-  # NOTE: The nebula certificate of the "via" node *MUST* have the "route" defined as a subnet in its certificate
-  unsafe_routes:
-    #- route: 172.16.1.0/24
-    #  via: 192.168.100.99
-    #  mtu: 1300 #mtu will default to tun mtu if this option is not sepcified
-
-
-# TODO
-# Configure logging level
-logging:
-  # panic, fatal, error, warning, info, or debug. Default is info
-  level: info
-  # json or text formats currently available. Default is text
-  format: text
-  # Disable timestamp logging. useful when output is redirected to logging system that already adds timestamps. Default is false
-  #disable_timestamp: true
-  # timestamp format is specified in Go time format, see:
-  #     https://golang.org/pkg/time/#pkg-constants
-  # default when `format: json`: "2006-01-02T15:04:05Z07:00" (RFC3339)
-  # default when `format: text`:
-  #     when TTY attached: seconds since beginning of execution
-  #     otherwise: "2006-01-02T15:04:05Z07:00" (RFC3339)
-  # As an example, to log as RFC3339 with millisecond precision, set to:
-  #timestamp_format: "2006-01-02T15:04:05.000Z07:00"
-
-#stats:
-  #type: graphite
-  #prefix: nebula
-  #protocol: tcp
-  #host: 127.0.0.1:9999
-  #interval: 10s
-
-  #type: prometheus
-  #listen: 127.0.0.1:8080
-  #path: /metrics
-  #namespace: prometheusns
-  #subsystem: nebula
-  #interval: 10s
-
-  # enables counter metrics for meta packets
-  #   e.g.: `messages.tx.handshake`
-  # NOTE: `message.{tx,rx}.recv_error` is always emitted
-  #message_metrics: false
-
-  # enables detailed counter metrics for lighthouse packets
-  #   e.g.: `lighthouse.rx.HostQuery`
-  #lighthouse_metrics: false
-
-# Handshake Manager Settings
-#handshakes:
-  # Handshakes are sent to all known addresses at each interval with a linear backoff,
-  # Wait try_interval after the 1st attempt, 2 * try_interval after the 2nd, etc, until the handshake is older than timeout
-  # A 100ms interval with the default 10 retries will give a handshake 5.5 seconds to resolve before timing out
-  #try_interval: 100ms
-  #retries: 20
-  # trigger_buffer is the size of the buffer channel for quickly sending handshakes
-  # after receiving the response for lighthouse queries
-  #trigger_buffer: 64
-
-
-# Nebula security group configuration
-firewall:
-  conntrack:
-    tcp_timeout: 12m
-    udp_timeout: 3m
-    default_timeout: 10m
-    max_connections: 100000
-
-  # The firewall is default deny. There is no way to write a deny rule.
-  # Rules are comprised of a protocol, port, and one or more of host, group, or CIDR
-  # Logical evaluation is roughly: port AND proto AND (ca_sha OR ca_name) AND (host OR group OR groups OR cidr)
-  # - port: Takes `0` or `any` as any, a single number `80`, a range `200-901`, or `fragment` to match second and further fragments of fragmented packets (since there is no port available).
-  #   code: same as port but makes more sense when talking about ICMP, TODO: this is not currently implemented in a way that works, use `any`
-  #   proto: `any`, `tcp`, `udp`, or `icmp`
-  #   host: `any` or a literal hostname, ie `test-host`
-  #   group: `any` or a literal group name, ie `default-group`
-  #   groups: Same as group but accepts a list of values. Multiple values are AND'd together and a certificate would have to contain all groups to pass
-  #   cidr: a CIDR, `0.0.0.0/0` is any.
-  #   ca_name: An issuing CA name
-  #   ca_sha: An issuing CA shasum
-
-  outbound:
-    # Allow all outbound traffic from this node
-    - port: any
-      proto: any
-      host: any
-
-  inbound:
-    - port: any
-      proto: any
-      host: any
diff --git a/charts/vpn-mesh-config/templates/lighthouse-config.yaml b/charts/vpn-mesh-config/templates/lighthouse-config.yaml
index b318546..7ce6c0a 100644
--- a/charts/vpn-mesh-config/templates/lighthouse-config.yaml
+++ b/charts/vpn-mesh-config/templates/lighthouse-config.yaml
@@ -4,4 +4,43 @@
   name: lighthouse-config
   namespace: {{ .Release.Namespace }}
 data:
-{{ (.Files.Glob "lighthouse.yaml").AsConfig | replace "<INTERNAL_IP>" .Values.lighthouse.internalIP | replace "<EXTERNAL_IP>" .Values.lighthouse.externalIP | replace "<PORT>" .Values.lighthouse.port | indent 2 }}
+  lighthouse.yaml: |
+    pki:
+      ca: /etc/nebula/lighthouse/ca.crt
+      cert: /etc/nebula/lighthouse/host.crt
+      key: /etc/nebula/lighthouse/host.key
+    static_host_map:
+      "{{ .Values.lighthouse.internalIP }}": ["{{ .Values.lighthouse.externalIP }}:{{ .Values.lighthouse.port }}"]
+    lighthouse:
+      am_lighthouse: true
+      interval: 60
+    listen:
+      host: "[::]"
+      port: {{ .Values.lighthouse.port }}
+    punchy:
+      punch: true
+    cipher: chachapoly
+    tun:
+      disabled: false
+      dev: nebula1
+      drop_local_broadcast: false
+      drop_multicast: false
+      tx_queue: 500
+      mtu: 1300
+    logging:
+      level: info
+      format: text
+    firewall:
+      conntrack:
+        tcp_timeout: 12m
+        udp_timeout: 3m
+        default_timeout: 10m
+        max_connections: 100000
+      outbound:
+        - port: any
+          proto: any
+          host: any
+      inbound:
+        - port: any
+          proto: any
+          host: any